If you are looking for car amplifier 4 channel I want to help you. The tools we buy come with standard and simple music systems. If you are a fan of quality, clean sound and powerful bass system, we need to invest in extra equipment. Below, we have listed 3 of the most preferred brands and models for you.
1. Kicker 46CXA3604 Car Amplifier 4 Channel
Kicker CX360.4 car amplifier 4 channel
Using Class A/B power, this amp features a variable bass boost with KickEQ, giving you as much as a 6dB of extra bump. A powerful 12dB crossover is also included, letting you quickly tune your system to perfection.
CX-Series Amplifiers accept up to 40 volts (400 watts) of speaker-level input signal. This kind of flexibility both makes line-out converters unnecessary and optimizes your sound quality at the same time!
Highly efficient heat sinks keep the amp cool with a sophisticated new look, while KICKER’s FIT+ (Fail-safe Integration Technology-PLUS), gives you outstanding noise rejection - even with premium factory audio systems.
This CX-Series Amplifier delivers as much as 90 watts into four full-range channels, or 180 watts into two bridged channels.
Class A/B full-range channels
Three-second turn-on/off delay to eliminate unwanted interference
Variable 12dB crossovers provides control to dial in perfect sound
KickEQ 6dB variable bass boost for those additional low frequencies
FIT+ (Fail-safe Integration Technology-PLUS) means it works with nearly every radio
Accepts up to 40-volt input signal
Small footprint for easier installation
Vertical mounting hardware included for another unique look
Compatible with CXARC Remote Bass Control
Power (watts/ch) 4 Ohm Stereo - 65x4
Power (watts/ch) 2 Ohm Stereo - 90x4
Power (watts/ch) 4 Ohm Mono - 180x2
CXRC Remote Bass Capable (sold sep.) yes
Dimensions (in, cm): (Height: 2-3/8, 5.9; Width: 6-3/4, 17; Length: 12-1/2, 31.7
Frequency Response (Hz): 10Hz-20kHz
Input Sensitivity: 250mV-10V (Low Level); 1V-40V (High Level)
Signal-to-Noise Ratio: 95dB
Active Crossover: HI, LO or OFF; Variable 50–200Hz @ 12dB/Octave
Subsonic Filter: n/a
KickEQ Boost Variable 0-6dB @40Hz
Customer questions & answers
Question: Whats the difference between this model and this one kicker 46cxa360.4t?
Answer: The 360.4T is just denoting a different production facility. It is the exact same amplifier.
Question: Is this good to use on 4 separate 6-1/2 kicker CS series speakers rated for 300W max?
Answer: You really need to know the RMS (continuous power) rating of the speakers. Without knowing the RMS rating it is hard to say. However, I can tell you that this car audio amplifier performs very well with my two Kicker 3-1/2" and two Kicker 4"x10" speakers.
Love this car amplifier 4 channel it putts out good power and sound.
2. Alpine MRV-F300 4 Channel Car Amplifier
In 4-channel mode the Alpine MRV-F300 delivers 50 watts RMS to each of your car's front and rear speakers, making for some sweet sound on your drive. You can also run this amp in 3-channel mode, powering a subwoofer with 150 watts RMS while driving a pair of full-range speakers with 50 watts each. If you need a good amp for bass, you can switch the amp to 2-channel mode and send up to 150 watts RMS each to a pair of subwoofers.
The MRV-F300 car amplifier 4 channel uses a technology called Enhanced Shutdown Performance, which rolls back the output a bit when the amp threatens to overheat from playing at its limits too long. Instead of shutting down completely, it continues playing your music, until it cools enough to return to full power.
High- and low-pass filters put you in command of the frequencies that reach your speakers, while a bass boost lets you apply some extra low-end punch. The car audio amplifier includes preamp- and speaker-level inputs, so you can install it in almost any vehicle, even one with a factory radio. If you're using the speaker-level inputs, the amp senses an incoming signal and turns itself on, eliminating the need to run a turn-on wire back to your vehicle's receiver or fusebox. If you're a tweaker, you'll appreciate the end-piece terminal covers that can be snapped in and out without the need for any tools.
(product description: http://www.audioplanetny.com/Car_Audio/Car_Amplifiers/Alpine_MRV-F300_Compact_Car_Amplifier/pid/1338/185)
4-channel car amplifier
50 watts RMS x 4 at 4 ohms (75 watts RMS x 4 at 2 ohms)
150 watts RMS x 2 bridged output at 4 ohms (4-ohm stable in bridged mode)
variable high- and low-pass filters (50-400 Hz, 12 dB/octave)
selectable bass boost (+12 dB at 50 Hz) on channels 3 & 4
MOSFET power supply
preamp and speaker-level inputs
Remote Sensing automatic turn-on when using speaker-level inputs
gold-plated screw terminals
fuse rating: 40A x 1
8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
8-1/4"W x 2-3/16"H x 7-15/16"D
Question: Is this amp auto power on when there’s a speaker input?
Answer: Yes, the amp has auto-sensing remote on when using the speaker inputs.
Question: so this amp doesn't have seperate gain controls for the front and rear channels?
Answer: Yes, there are separate gain controls.
Question: can this amp handle 4 infinity reference 6.5 to there maximum power?
Answer: Yes, this amp definetly has the power to crank 4 61/2 speakers. I currently have the amp powering 2 alpine 6x9's in the back and 2 alpine 6.5 in the front. It sounds wonderful, the more volume you give them the clearer they sound. You need to remember that you will also have more power coming from the car stereo as well.
I bought this car audio amplifier to power 4 JL audio speakers. The Alpine head unit I have provides a maximum of 18 watts RMS/channel. This 4 channel amp helps the head unit power the speakers by adding 50 watts RMS/channel. And the added power is clean and precise. I can detect no hum, static, or distortion, even at high listening levels.
This car amplifier 4 channel is a bargain. I would buy it again without hesitation. If you are looking for good, clean sound, look no further. This one will not disappoint.
3. Taramp's DS 800x4 4 channel amp
The DS 800×4 amplifier module is carefully developed with state-of-the-art technology, offering high efficiency and performance for automotive audio systems. Classified as Multi-channel, it has a maximum power of 800 watts RMS, running at a 2-ohm impedance, with four 200 watts RMS channels. It is FULL-RANGE, operating on all frequencies in the right measure.
Number of Channels: 4
Max Output Power:
@ 12,6 VDC - 2 OHMs: 800W RMS (4 x 200W RMS)
@ 12,6 VDC - 4 OHMS: 544W RMS (4 x 136W RMS)
Signal Noise/Ratio: >88dB
Frequency Response: 10Hz ~ 45KHz (-3dB)
Input Impedance: 18K OHMS
Minimum Supply Voltage: 9 VDC
Maximum Supply Voltage: 16 VDC
Idle Consumption: 1.4A
Maximum Musical Consumption: @ 12,6 VDC: 43A
Sinusoidal Signal Maximum Consumption: (1KHz) 12,6VDC: 86A
Dimensions (WxHxD): 182 x 52 x 227mm
Customer questions & answers
Question: What is the total harmonic distortion for the rated wattages?
Answer: In maximum power, it will have a distortion of <= 1%, as indicated in the manual.
Question: can this amp be used to power a set of component speakers on two channels and two 2 ohm subwoofers on the other two channels?
Answer: Yes, it has 4 channels, so you can connect 2 speakers and 2 subwoofers. But you have to check the impedance and RMS power of the speakes and subwoofers to see if they are all within the specifications for the DS800X4.
Question: Can this move 4 Ds18 6.5 speaker with 380w 90rms 8 ohms each one?
Answer: Yes - you can use one speaker per channel with the DS800X4 and your Ds18 6.5 speakers.
Awesome amp!! This 4 channel amp works perfect for my two selenium D-250x and 2 selenium super tweeters. Very powerful, I have the knob barely passed minimum and my drivers are SCREAMING, that powerful. I also have a Taramp's 2500HD pushing 2 Eros 450 rms and I couldn't be happier with my set up. Can't go wrong with Taramp's. Thanks guys!